An ESP-IDF port of the LogicData protocol implementation that acts as a man-in-the-middle interface between your standing desk's control buttons and the table controller. This project allows you to intercept desk height information and add smart automation features to your LogicData-compatible standing desk.
This project implements a passive listener that intercepts the serial communication between the desk controller and handset, allowing you to:
- Monitor desk height in real-time
- Set height presets by pressing both buttons simultaneously
- Automatic positioning with double-click to saved heights
- Manual control with long-press pass-through to original desk functions
Caution
This interface may violate your LOGICDATA warranty.
Use at your own risk!
- Any ESP development board, I used ESP32
- Logic level shifter (3.3V to 5V) for reliable operation
- Breadboard or PCB for connections
- Dupont wires or appropriate connectors
| Function | ESP32 GPIO | Description |
|---|---|---|
| LogicData RX | GPIO 25 | Serial data from desk controller |
| Desk UP Control | GPIO 27 | UP signal to desk controller |
| Desk DOWN Control | GPIO 26 | DOWN signal to desk controller |
| User Button UP | GPIO 21 | Physical button for UP commands |
| User Button DOWN | GPIO 19 | Physical button for DOWN commands |
Controller pinout is shown in the picture below
Every connector visualization is the front (as looking directly into the connector)
- Check all the wires are connected - from the destination to the source is 0 Ω
- Check if all the wires are not touching themselves - if made in the air instead of breadboard use "onion isolation"
- Check if the correct wires are wired - the faces of connectors changes as a female/male connector
- Long Press UP/DOWN: Direct control of desk movement (pass-through)
- Double-click UP: Move to saved high position
- Double-click DOWN: Move to saved low position
- Press both UP+DOWN simultaneously: Save current height as preset
- Real-time height monitoring and logging
- Automatic height presets (learns your preferred positions)
- Smooth automatic positioning to saved heights
- Non-volatile preset storage (NVS) - preset heights are automatically saved and persist across power cycles
- Automatic preset management - presets are updated and saved whenever you set new positions
The SmartDesk controller uses ESP32's Non-Volatile Storage (NVS) to persistently store preset heights:
- Automatic Saving: Preset heights are automatically saved to NVS whenever they are updated
- Persistent Storage: Presets survive power cycles, firmware updates, and system resets
- Namespace: Uses "smartdesk" namespace for organized storage
- Keys: Stores "low_height" and "high_height" as 8-bit values
- Error Handling: Graceful fallback to defaults if NVS operations fail
The LOGICDATA protocol operates at:
- Speed: 1000 bps (1 bit per millisecond)
- Voltage: 5V logic levels
- Format: 32-bit words with specific framing
- Idle state: Logic HIGH (5V)
- Data encoding: Inverted Manchester encoding
For detailed protocol analysis, see the technical blog post.
-
Clone and build:
git clone <this-repository> cd LogicData_SmartDesk idf.py set-target <your chip type> idf.py build
-
Flash to ESP32:
idf.py flash monitor
-
Wire connections according to the pin diagram above
-
Test functionality by observing serial output during desk operation
The table operates at 5V, pin controlling is okay, but pin for receiving data from the table controller is under stress, because Espressif SoCs are meant to be operated on 3.3V logic.
This project is an ESP-IDF port of the excellent work by:
- Original Arduino Implementation: @phord/RoboDesk - Arduino code for LOGICDATA protocol
- Protocol Analysis: Hacking the Logicdata Desk Controller - Detailed reverse engineering blog post
Major differences from the original:
- Ported from Arduino to ESP-IDF framework
- Added preset height functionality
- Implemented automatic positioning system
- Enhanced button control with multiple gesture support
This project is licensed under the MIT License - see the LICENSE file for details.
Contributions are welcome! Please feel free to submit pull requests or open issues for bugs and feature requests.