Conversation
…intervals (#900) * docs(air1): rebuild Sensor Definitions with tabbed layout and update intervals Replace the old stacked sections with a single Controls/Sensors/ Configuration/Diagnostic tab strip backed by tables. Add a Default Update column sourced from firmware, split the optional MICS gas sensor into its own table with a safety/accuracy warning and a link to the DFRobot SEN0377 wiki, and document the v26.3.2.1 entities (Apollo Firmware Version, ESPHome Version, IP Address, NowCast AQI, DPS310 Pressure Offset). * docs(air1): rename Firmware row to Firmware Update Match the device's actual OTA update entity name and clarify it is separate from the Apollo Firmware Version and ESPHome Version sensors.
…intervals (#901) * docs(mtr1): rebuild Sensor Definitions with tabbed layout and update intervals Convert the stacked collapsibles to a Controls/Sensors/Configuration/ Diagnostic tab strip with tables. Split Sensors into air-quality and radar (LD2450) subsections, add a Default Update column sourced from firmware (v26.3.2.1), and document the firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address) plus the SCD40/DPS310 offsets and LTR390 Update Interval. Fix the title typo. * docs(mtr1): rename Firmware row to Firmware Update Match the device's actual OTA update entity name and clarify it is separate from the Apollo Firmware Version and ESPHome Version sensors.
…intervals (#902) Convert the stacked collapsibles to a Controls/Sensors/Events/ Configuration/Diagnostic tab strip with tables. Add a Default Update column sourced from firmware (v26.3.2.1) and document the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address) plus the ESP Reboot and Factory Reset ESP buttons.
… intervals (#903) Convert the stacked collapsibles to a Controls/Sensors/Configuration/ Diagnostic tab strip with tables. Add a Default Update column sourced from firmware (v26.3.2.1), document the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address), and surface the full pump-control/safety settings (Invert Water Logic, Auto Refill, Max Safe Run Time).
… intervals (#904) Convert the stacked collapsibles to a Controls/Sensors/Configuration/ Diagnostic tab strip with tables. Add a Default Update column sourced from firmware (v26.3.2.1), document the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address), and correct the Select Probe / offset names and the 8-minute Sleep Duration default. Convert the Homey mirror to a snippet so it inherits the rebuilt page.
…e intervals (#905) Convert the stacked collapsibles to a Controls/Sensors/Configuration/ Diagnostic tab strip with tables. Add a Default Update column sourced from firmware (v26.3.2.1), document the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address) and the battery sensors, and correct the Select Probe / Temp Probe Offset names. Convert the Homey mirror to a snippet so it inherits the rebuilt page.
…intervals (#907) * docs(msr1): rebuild Sensor Definitions with tabbed layout and update intervals Modernize the oldest plain-bullet page into a Controls/Sensors/ Configuration/Diagnostic tab strip with tables (adding frontmatter it never had). Split Sensors into air-quality/light and radar (LD2410) subsections, add a Default Update column sourced from firmware (v26.3.2.1), and document the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address). Drop the stale 'removed in vX' rows and point the radar tuning links at the current zones-ha guide. * docs(msr1): add Firmware Update diagnostic entity Home Assistant auto-creates the firmware update entity from the device's project block; document it alongside the Apollo Firmware Version and ESPHome Version sensors.
…intervals (#908) * docs(msr2): rebuild Sensor Definitions with tabbed layout and update intervals Convert the stacked collapsibles to a Controls/Sensors/Configuration/ Diagnostic tab strip with tables, splitting Sensors into air-quality/ light and radar (LD2410) subsections. Add a Default Update column sourced from firmware (v26.3.2.1) and the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address). Preserve the DPS310 'small subset of devices' note and LD2410 firmware-version note. * docs(msr2): add Firmware Update diagnostic entity Home Assistant auto-creates the firmware update entity from the device's project block; document it alongside the Apollo Firmware Version and ESPHome Version sensors.
… intervals (#909) * docs(rpro1): rebuild Sensor Definitions with tabbed layout and update intervals Convert the nested collapsibles to a Controls/Sensors/Configuration/ Diagnostic tab strip with tables. Split Sensors into air-quality/ light, LD2412 presence, and LD2450 tracking subsections, and split Configuration by radar. Add a Default Update column sourced from firmware (v25.11.20.1) and document the firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address). Consolidate the LD2450 Target/Zone rows and the LD2412 g00-g13 gate rows. * docs(rpro1): restore Combined Presence sensor The live page documents and recommends Combined Presence (Detected when either radar sees a target). It is not in the v25.11.20.1 firmware clone I read, so add it back as its own subsection. * docs(rpro1): bump firmware version reference to 26.3.2.1 Confirmed against the merged R_PRO-1 firmware (26.3.2.1); the only entity delta from the earlier clone was Combined Presence, already documented.
…intervals (#910) Convert to a Controls/Sensors/Configuration/Diagnostic tab strip with tables and a Default Update column sourced from firmware (v26.3.2.1). Drop the raw ESPHome component-config dump in favor of the HA entity definitions, document the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address), and correct the Sleep Duration / 100% Water Voltage defaults. Convert the Homey mirror to a snippet so it inherits the rebuilt page.
… intervals (#911) Convert to a Controls/Sensors/Configuration/Diagnostic tab strip with tables and a Default Update column sourced from firmware (v26.3.2.1). Drop the raw ESPHome component-config dump in favor of the HA entity definitions, document the new firmware-version entities (Apollo Firmware Version, ESPHome Version, IP Address) and the 18650 battery sensors, and correct the Sleep Duration / 100% Water Voltage defaults. Convert the Homey mirror to a snippet so it inherits the rebuilt page.
|
Important Review skippedAuto reviews are disabled on base/target branches other than the default branch. 🗂️ Base branches to auto review (1)
Please check the settings in the CodeRabbit UI or the ⚙️ Run configurationConfiguration used: Organization UI Review profile: CHILL Plan: Pro Run ID: You can disable this status message by setting the Use the checkbox below for a quick retry:
✨ Finishing Touches🧪 Generate unit tests (beta)
Thanks for using CodeRabbit! It's free for OSS, and your support helps us grow. If you like it, consider giving us a shout-out. Comment |
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
1 participant
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
Sync
devintomain. Includes the rebuilt Sensor Definitions pages for AIR-1, MTR-1, BTN-1, PUMP-1, TEMP-1, TEMP-1B, MSR-1, MSR-2, R-PRO-1, PLT-1, and PLT-1B: tabbed Controls/Sensors/Configuration/Diagnostic layout, firmware-sourced Default Update column, and the Firmware Update / ESPHome Version / Apollo Firmware Version entities.