Controller seems to have no response after a period of time

[Wirepower]

I have it all working etc, the. After about an hour or so, it loses communication, it shows the last update but if I try to open a valve it doesn’t respond. The only way to fix it is by reloading the integration.
Anyone else having this issue?

[chickymonkey]

I am experiencing same issue, here is some debug, my heater is in the ceiling, and the wifi module is a few meters away:

2025-07-18 21:48:30.195 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.receiver] Fired off command: (N000001{"HGOM": {"GSO": {"SP": "21" } } })
2025-07-18 21:48:31.195 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.receiver] Sequence: 1 Json: [{"SYST": {"CFG": {"MTSP": "N", "NC": "00", "TU": "C", "CF": "1", "VR": "0187", "CV": "0011", "CC": "197", "ZA": "                ", "ZB": "                ", "ZC": "                ", "ZD": "                " }, "AVM": {"HG": "Y", "EC": "N", "CG": "N", "RA": "N", "RH": "N", "RC": "N" }, "OSS": {"DY": "FRI", "TM": "21:47", "BP": "Y", "RG": "Y", "ST": "N", "MD": "H", "AT": "999", "LO": "N" }, "FLT": {"AV": "N", "C3": "000" } } },{"HGOM": {"CFG": {"ZUIS": "Y", "ZAIS": "N", "ZBIS": "N", "ZCIS": "N", "ZDIS": "N", "CF": "N", "PS": "Y", "DG": "W" }, "OOP": {"ST": "N", "CF": "N", "FL": "00", "SN": "N", "DA": "N", "DT": "E", "DS": "N" }, "GSO": {"OP": "M", "SP": "21", "AO": "N" }, "GSS": {"HC": "Y", "FS": "Y", "GV": "Y", "PH": "N", "AT": "W", "AZ": "W" }, "APS": {"AV": "N" }, "ZUO": {"UE": "Y" }, "ZAO": {"UE": "N" }, "ZBO": {"UE": "N" }, "ZCO": {"UE": "N" }, "ZDO": {"UE": "N" }, "ZUS": {"AE": "Y", "MT": "173" }, "ZAS": {"AE": "N", "MT": "173" }, "ZBS": {"AE": "N", "MT": "173" }, "ZCS": {"AE": "N", "MT": "173" }, "ZDS": {"AE": "N", "MT": "173" } } }]
2025-07-18 21:48:31.196 DEBUG (Thread-6 (poll_loop)) [pyrinnaitouch.system_status] We are in HEAT mode
2025-07-18 21:48:31.196 DEBUG (Thread-6 (poll_loop)) [pyrinnaitouch.unit_status] Unit is ON
2025-07-18 21:48:31.196 DEBUG (Thread-6 (poll_loop)) [pyrinnaitouch.unit_status] Fan Speed is: 00
2025-07-18 21:48:31.196 DEBUG (Thread-6 (poll_loop)) [pyrinnaitouch.unit_status] Unit OpMode is: M
2025-07-18 21:48:31.196 DEBUG (Thread-6 (poll_loop)) [pyrinnaitouch.unit_status] Unit set temp is: 21
2025-07-18 21:48:31.196 DEBUG (Thread-6 (poll_loop)) [custom_components.rinnaitouch.climate] Ext. temp sensor entity name: sensor.rinnai_touch_main_target_temperature_sensor
2025-07-18 21:48:31.196 DEBUG (Thread-6 (poll_loop)) [custom_components.rinnaitouch.climate] Ext. temp sensor reports: 20.0
2025-07-18 21:48:31.197 DEBUG (Thread-6 (poll_loop)) [custom_components.rinnaitouch.climate] Ext. temp sensor entity name: sensor.broadlink_livingroom_temperature
2025-07-18 21:48:31.197 DEBUG (Thread-6 (poll_loop)) [custom_components.rinnaitouch.climate] Ext. temp sensor reports: 16.98
2025-07-18 21:48:31.198 DEBUG (MainThread) [custom_components.rinnaitouch.climate] Internal temperature sensor reports: 999
2025-07-18 21:48:31.201 ERROR (MainThread) [homeassistant.components.homekit.type_thermostats] Cannot map hvac target mode: heat to homekit as only {0: <HVACMode.OFF: 'off'>, 2: <HVACMode.FAN_ONLY: 'fan_only'>} modes are supported
2025-07-18 21:48:31.201 ERROR (MainThread) [homeassistant.components.homekit.type_thermostats] Cannot map hvac target mode: heat to homekit as only {0: <HVACMode.OFF: 'off'>, 2: <HVACMode.FAN_ONLY: 'fan_only'>} modes are supported
2025-07-18 21:48:31.201 ERROR (MainThread) [homeassistant.components.homekit.type_thermostats] Cannot map hvac target mode: heat to homekit as only {0: <HVACMode.OFF: 'off'>, 2: <HVACMode.FAN_ONLY: 'fan_only'>} modes are supported
2025-07-18 21:48:32.208 ERROR (Thread-7 (receiver)) [pyrinnaitouch.receiver] Socket timed out, renewing connection (TimeoutError('timed out'))
2025-07-18 21:48:32.209 DEBUG (Thread-7 (receiver)) [pyrinnaitouch.connection] Connection successfully closed
2025-07-18 21:48:32.209 DEBUG (Thread-7 (receiver)) [pyrinnaitouch.connection] Error 1st phase during renewConnection [Errno 9] Bad file descriptor
2025-07-18 21:48:32.210 DEBUG (Thread-7 (receiver)) [pyrinnaitouch.connection] Creating new client...
2025-07-18 21:48:32.211 ERROR (Thread-5 (receiver)) [pyrinnaitouch.receiver] Socket timed out, renewing connection (OSError(9, 'Bad file descriptor'))
2025-07-18 21:48:32.211 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Exception during client shutdown [Errno 9] Bad file descriptor
2025-07-18 21:48:32.211 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Error 1st phase during renewConnection [Errno 9] Bad file descriptor
2025-07-18 21:48:32.211 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Creating new client...
2025-07-18 21:48:32.408 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Client connection created: ('192.168.3.125', 27847)
2025-07-18 21:48:32.408 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Connected to ('192.168.3.125', 27847)
2025-07-18 21:48:32.664 ERROR (Thread-5 (receiver)) [pyrinnaitouch.receiver] Couldn't decode JSON (connection), skipping (ConnectionResetError(104, 'Connection reset by peer'))
2025-07-18 21:48:32.664 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Exception during client shutdown [Errno 107] Socket not connected
2025-07-18 21:48:32.665 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Error 1st phase during renewConnection [Errno 107] Socket not connected
2025-07-18 21:48:32.665 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Creating new client...
2025-07-18 21:48:32.713 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Client refused connection: [Errno 111] Connection refused
2025-07-18 21:48:32.714 DEBUG (Thread-5 (receiver)) [pyrinnaitouch.connection] Error during renewConnection [Errno 111] Connection refused

I have removed Rinnai's APP after connecting it to home wifi, wifi 5G mode is disabled.

Any help appreciated.

[chickymonkey]

I’m using NC-6s with starpro 4 gas heater.