diff --git a/docs/homey/products/plt1b/additional-info/insert-battery.md b/docs/homey/products/plt1b/additional-info/insert-battery.md new file mode 100644 index 0000000000..dbff49f0bb --- /dev/null +++ b/docs/homey/products/plt1b/additional-info/insert-battery.md @@ -0,0 +1 @@ +--8<-- "products/plt1b/additional-info/insert-battery.md:5:" diff --git a/docs/homey/products/plt1b/setup/insert-battery.md b/docs/homey/products/plt1b/setup/insert-battery.md deleted file mode 100644 index 288121913a..0000000000 --- a/docs/homey/products/plt1b/setup/insert-battery.md +++ /dev/null @@ -1,33 +0,0 @@ -# How to Insert the Battery - -!!! info "18650 battery and charger required!" - - The PLT-1B does *NOT* include a battery nor a charging circuit. You will need to supply your own flat-top, unprotected 18650 Li-ion cell, and a separate 18650 charger. Recommended cell: Samsung 30Q 18650 3000mAh. - -1\. Gently press your thumb on the case above the stake and the lid should pop off. - -![](/assets/plt-1b-remove-case-lid.webp) - -2\. Hold the case and push the stake down a bit, then gently lift it out of the bottom case section. - -![](/assets/plt-1b-lift-pcb-out-of-case.webp) - -3\. Flip the PLT-1B over and identify the `+` and `-` markings. The `+` is on the left side and the `-` is on the right side. Double check before going any further. - -4\. The top of the battery (the positive end, marked with a `+` and a small ring around the terminal) goes on the left side, matching the `+` on the PLT-1B. - -![](/assets/plt-1b-identify-top-of-18650-battery.webp) - -5\. Hold the PCB. You'll need to use a bit of force to push in the battery. Start with the right `-` side, then push in the left `+` side. - -![](/assets/plt-1b-insert-battery.webp) - -6\. Flip the sensor back over and lay the PCB inside the case so it sits flat. - -![](/assets/plt-1b-place-pcb-in-case.webp) - -7\. Line up the notch in the top left of the lid, then gently press down until the lid snaps into place. - -![](/assets/plt-1b-replace-case-lid.webp) - -You have now installed or reinstalled the battery! diff --git a/mkdocs.yml b/mkdocs.yml index 882d6165cb..90f9fde75a 100755 --- a/mkdocs.yml +++ b/mkdocs.yml @@ -98,8 +98,6 @@ plugins: 'homey/products/msr2/calibrating-and-updating/updating-msr-2-firmware.md': 'homey/products/msr2/setup/updating-msr-2-firmware.md' 'homey/products/msr2/calibrating-and-updating/zones-ha.md': 'homey/products/msr2/setup/zones-ha.md' 'homey/products/msr2/calibrating-and-updating/zones-hlk.md': 'homey/products/msr2/setup/zones-hlk.md' - # PLT-1B Insert Battery: setup -> additional-info - 'products/plt1b/setup/insert-battery.md': 'products/plt1b/additional-info/insert-battery.md' extra: social: @@ -755,7 +753,7 @@ nav: - Calibrating Soil Moisture: homey/products/plt1b/calibrate-plt1.md - Prevent Sleep: homey/products/plt1b/setup/prevent-sleep.md - How To Wake Up Your Sensor: homey/products/plt1b/battery-sensors/wake-up-battery-sensor.md - - Insert Battery: homey/products/plt1b/setup/insert-battery.md + - Insert Battery: homey/products/plt1b/additional-info/insert-battery.md - Sensor Connection Check: homey/products/plt1b/battery-sensors/sensor-connection-check.md - Reviews: homey/products/plt1b/reviews.md - Examples: